Hoffman Amplifiers Tube Amplifier Forum
Amp Stuff => EZ Board postings => Topic started by: Geezer on June 18, 2005, 05:15:14 am
-
Hoffman Amplifiers
> Tube Amp Building - Tweaks - Repairs
> Single channel Fender with reverb layout
<< Prev Topic | Next Topic >>
Author Comment
Deadbeat2
Junior tube assistant
Posts: 1
(12/27/03 11:53 am)
Single channel Fender with reverb layout
--------------------------------------------------------------------------------
I am wanting to build a single channel Super Reverb or Deluxe Reverb with no tremelo. I haven't decided on output power yet. Anyway, Anyone know of a nice layout for this or should I just take a Fender layout and omit what I don't want? Anyone have such a layout handy to share? Thanks, Bruce J.
b4yourtime
Junior tube assistant
Posts: 51
(12/27/03 11:56 am)
Re: Single channel Fender with reverb layout
--------------------------------------------------------------------------------
I would be interested in the same project.......
Doug C.
Casey4s
Senior tube assistant
Posts: 126
(12/27/03 12:04 pm)
Re: Single channel Fender with reverb layout
--------------------------------------------------------------------------------
Look at a Princeton Reverb AA1164, for a DIY amp.
One channel, nice tone stack, 14 watts as is but you can build a 6L6 power section for the single channel pre amp and get around 40 watts.
That amp has an excellent tremolo without the "Opto-Roach", but you could easily leave it off if you so desire.
I just finished building a DIY BFPR and it has excellent tone, through a 12" AlNiCo speaker. Loud enough for small venues as is.
Good luck whatever you decide to build...
Deadbeat2
Junior tube assistant
Posts: 2
(12/27/03 10:41 pm)
Already have one
--------------------------------------------------------------------------------
Thanks Casey but I already have a '72 Princeton Reverb and a '66 Princeton. I guess what I want is a Princeton style amp with a LTP phase inverter. If I could figure out how to change the PI I guess I'd have it. I don't want to mod my Fender's, though, but build a new amp. Bruce J.
Dmichel1984
Junior tube assistant
Posts: 3
(3/9/04 5:10 am)
RE
--------------------------------------------------------------------------------
just follow the PR schematic up to the PI, then go SR... it wouldn't be hard at all
Dmichel1984
Junior tube assistant
Posts: 5
(3/9/04 5:16 am)
RE
--------------------------------------------------------------------------------
or stick the premier reverb circuit in there... then you'll basically be doing what I'm doing w/ my bandmaster, except i'm going w/ split-load PI
Funkalicousgroove
Junior tube assistant
Posts: 18
(3/11/04 3:55 pm)
I Have that schematic
--------------------------------------------------------------------------------
I Happen to have that exact schematic from a David Allen TONESavor, If you Like I can fax it to you or email it, it's not on line
ganzonimx
Hey get your own solder
Posts: 428
(3/11/04 4:49 pm)
Re: I Have that schematic
--------------------------------------------------------------------------------
I would apreciate to see that schematic. If possible please it mail to
ganzonim @ yahoo.com.mx
THX, Cris
Dmichel1984
Junior tube assistant
Posts: 16
(3/11/04 4:50 pm)
me?
--------------------------------------------------------------------------------
I didn't know if you were talking to me or? I'd like a copy of that schematic...DMichel123!!!!yahoo.com replace !!!! w/ @, duh
Funkalicousgroove
Junior tube assistant
Posts: 19
(3/11/04 6:17 pm)
Schematic
--------------------------------------------------------------------------------
I'll send it either later tonight or tomorrow, I have it at home- There is one extra control in the preamp called a "raw" control which acts to retrieve the signal sent to ground by the tone controls;IT CAN EASILY BE OMITTED.
Deadbeat2
Junior tube assistant
Posts: 3
(3/11/04 11:00 pm)
schematic
--------------------------------------------------------------------------------
Yes, Please send the schematic/layout. I'd like to have a look. Thanks! Bjoyce@jam.rr.com
tubejunky
Junior tube assistant
Posts: 1
(3/11/04 11:27 pm)
Layout?
--------------------------------------------------------------------------------
Do you have the layout too? Thanks acplink@earthlink.net
Funkalicousgroove
Junior tube assistant
Posts: 20
(3/12/04 12:50 pm)
Layout
--------------------------------------------------------------------------------
I do have the layout but it's too large to scan, any ideas???
bnwitt
Senior tube assistant
Posts: 295
(3/12/04 2:30 pm)
Re: Layout
--------------------------------------------------------------------------------
how about taking a digital photo of it?
Funkalicousgroove
Junior tube assistant
Posts: 21
(3/12/04 2:38 pm)
Re: Layout
--------------------------------------------------------------------------------
The only problem is it's a large Full color CAD drawing, I'll try it tonight. BTW did Everyone get the Schem OK?
tubejunky
Posts: 2
(3/12/04 4:36 pm)
Re: Layout
--------------------------------------------------------------------------------
Too large to take a picture of? Scan it in sections and photochop it together, or send the pieces to acplink@earthlink.net
Dmichel1984
Junior tube assistant
Posts: 24
(3/12/04 9:31 pm)
Re: Layout
--------------------------------------------------------------------------------
cool schematic... i'm gonna do something similar...
ganzonimx
Hey get your own solder
Posts: 429
(3/12/04 10:00 pm)
didn't get the schematic
--------------------------------------------------------------------------------
Hi Funkygroove
I din'd get the schematic yet, ganzonimx%%%yahoo.com.mx, you might have forgotten to pot a mx behind thye com?
Cris
bnwitt
Senior tube assistant
Posts: 296
(3/13/04 12:32 pm)
Re: Layout
--------------------------------------------------------------------------------
Funk,
I'd like a copy of the schematic as well. If you can take a decent digital pic of the layout, I could redraw it in Visio for everone that wants it.
Barry
jbrew73
Junior tube assistant
Posts: 106
(3/13/04 2:38 pm)
Re: Layout
--------------------------------------------------------------------------------
hey funk-groove
i would like a copy of the schematic when you get time.
thanks
john
Dmichel1984
Junior tube assistant
Posts: 26
(3/13/04 5:43 pm)
hahaha
--------------------------------------------------------------------------------
what did you get yourself into??
<< Prev Topic | Next Topic >>
Topic Commands
Click to receive email notification of replies
jump to: Tube Amp Building - Tweaks - Repairs (New)New Product Suggestions (New)Praises - Complaints - Suggestions (New)Buy - Sell- Trade (New)Archives (New)
- Hoffman Amplifiers - Tube Amp Building - Tweaks - Repairs - Hoffman Amplifiers -
Powered By ezboard® Ver. 7.32
Copyright ©1999-2005 ezboard, Inc.