Welcome To the Hoffman Amplifiers Forum

September 06, 2025, 04:41:52 pm
guest image
Welcome, Guest. Please login or register.
-User Name
-Password



Hoffman Amps Forum image Author Topic: Low output on 5E3  (Read 3072 times)

0 Members and 1 Guest are viewing this topic.

Offline allaboutone

  • Level 1
  • *
  • Posts: 2
Hoffman Amps Forum image
Low output on 5E3
« on: October 15, 2010, 01:39:40 pm »
New here and see there is a lot of valuable information so hope to visit often.I have a homebuild 5E3 that is about 10 years old.Always worked perfect until loaning it to a friend.He had a couple years and recently brought it back.He forgot to shut his tailgate and it took a spill out of the truck.It is a head and bottom.The only visible damage was a few scratches to the walnut head.It now has about 1/3 of the output that it should and is distorted.I have repalced all of the tubes with no change.Checked every solder joint and component in the amp with a DMM.I just can't see the problem.
Especially after checking the voltages .Pin 3 on the power tubes measures 343VDC.I have 357 on the first filter cap,354 on the second and 258 on the third.V1 pin 1 is 130VDC and pin 6 is 141.V2 voltages are 206 on 1 and 190 on 6.These don't seem far out of line with the exception of 206 VDC on pin one of V2 being high.The amp is basically the stock Fender circuit with the exception of having a choke.Any help tracking down this issue would be much appreciated.

Offline FYL

  • Level 4
  • *****
  • Posts: 2313
Hoffman Amps Forum image
Re: Low output on 5E3
« Reply #1 on: October 15, 2010, 02:01:16 pm »
Check cathode resistors and caps, one or more could have been damaged. If a cap bypass is dead, gain will be much lower and sound will be distorted.

Check the screen resistors.

Offline allaboutone

  • Level 1
  • *
  • Posts: 2
Hoffman Amps Forum image
Re: Low output on 5E3
« Reply #2 on: October 16, 2010, 09:34:38 am »
Thanks for the reply.I have checked the screen resistors.The cathode resistor measures 247.5 so is ok and I've checked all of the bypass caps and filters with a capacitance meter and esr meter and the all check good..I have also inspected all of the grounds.I first thought it would be a bad ground bleeding off signal.Could it be the OT and still getting correct voltages.

Offline FYL

  • Level 4
  • *****
  • Posts: 2313
Hoffman Amps Forum image
Re: Low output on 5E3
« Reply #3 on: October 16, 2010, 10:58:10 am »
Have you also checked the RC cathode networks for the small tubes?


Offline mresistor

  • Global Moderator
  • Level 4
  • ******
  • Posts: 3209
  • resistance is futile
Hoffman Amps Forum image
Re: Low output on 5E3
« Reply #4 on: October 16, 2010, 02:01:12 pm »
Not to leave any stones unturned - did you try different speakers?  and have you checked the speaker output jack?

206vdc on v2 pin one is around 40vdc too high isn't it?  IN addition to what FYL mentioned ,for V2a check the plate load resistor and the interstage coupling cap; is it a .022uf ?



« Last Edit: October 16, 2010, 10:44:32 pm by mresistor »

 


Choose a link from the
Hoffman Amplifiers parts catalog
Mobile Device
Catalog Link
Yard Sale
Discontinued
Misc. Hardware
What's New Board Building
 Parts
Amp trim
Handles
Lamps
Diodes
Hoffman Turret
 Boards
Channel
Switching
Resistors Fender Eyelet
 Boards
Screws/Nuts
Washers
Jacks/Plugs
Connectors
Misc Eyelet
Boards
Tools
Capacitors Custom Boards
Tubes
Valves
Pots
Knobs
Fuses/Cords Chassis
Tube
Sockets
Switches Wire
Cable


Handy Links
Tube Amp Library
Tube Amp
Schematics library
Design a custom Eyelet or
Turret Board
DIY Layout Creator
File analyzer program
DIY Layout Creator
File library
Transformer Wiring
Diagrams
Hoffmanamps
Facebook page
Hoffman Amplifiers
Discount Program